The SmallRig Ballhead Clamp Double Ball Adapter review centers on a compact way to attach a camera accessory to a rod, tube, or compatible camera shoe.
Its clamp and articulated ball head make it a practical fit for DIY video rigs, provided your support and accessory stay within the stated size and load limits.
SmallRig Ballhead Clamp Review Summary
The quick verdict

1,000+ ratings
Read Amazon ReviewsSmallRig 2164-CF Ballhead Clamp Double Ball Adapter
A compact mounting option for DIY camera rigs that need to clamp onto a rod or tube and position a monitor, light, or small accessory.
- The bottom clamp jaws open up to 40 mm for attachment to compatible rods, tubes, or other supports.
- A 1/4-inch screw at the top provides a connection for a monitor, video light, microphone, or similar accessory.
- The double ball-head design provides 360-degree articulation for adjusting the accessory's angle.
- The single locking knob is intended to secure the joint and support quick adjustment.
Pros
- Combines a clamp base and articulated accessory mount in one compact unit.
- A 40 mm jaw opening supports a range of common rods and tubes within that diameter.
Consider before buying
- The clamp's stated 40 mm opening makes it unsuitable for supports wider than that.
- Conflicting maximum-load figures make it difficult to choose a setup based on a precise capacity; plan conservatively.
Read the full review summary
This SmallRig mount combines a clamp that opens up to 40 mm, a 1/4-inch screw, and a ball-head joint that rotates through 360 degrees.
Its aluminum-alloy construction and protective rubber pad suit creators who want to attach a monitor, light, microphone, or other small accessory without adding a longer arm.
The design is most compelling when you already have a suitable rod, tube, or shoe mount and want to position a lightweight accessory close to it.
Check the clamp's fit against your support and the accessory's connection before buying; the product details give inconsistent maximum-load figures, so treat the listed limits cautiously and avoid basing a setup on the higher number.
The buying factors
SmallRig Ballhead Clamp Scorecard
Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.
Mounting flexibility
A clamp base, shoe-mount option, and 1/4-inch screw support several rig configurations.
Angle adjustment
The ball head offers 360-degree articulation for positioning an attached accessory.
Accessory compatibility
The 1/4-inch screw supports common small video accessories, though buyers should confirm their device connection.
Compactness
At 163 g, the mount is a relatively compact way to add an attachment point.
Grip protection
A dense rubber pad is included at the clamp area to help protect the contacted surface.
Load-limit clarity
The supplied specifications give conflicting maximum-load figures, making conservative setup planning important.
Key Features and Specifications of SmallRig Ballhead Clamp
- The bottom clamp jaws open up to 40 mm for attachment to compatible rods, tubes, or other supports.
- A 1/4-inch screw at the top provides a connection for a monitor, video light, microphone, or similar accessory.
- The double ball-head design provides 360-degree articulation for adjusting the accessory's angle.
- The single locking knob is intended to secure the joint and support quick adjustment.
- The body is described as nearly all metal, made from aluminum alloy, with a dense rubber pad in the clamp area.
- The listed weight is 163 g, and the folded dimensions are 68.5 × 43 × 10 mm.
Pros and Cons of SmallRig Ballhead Clamp
Pros
- Combines a clamp base and articulated accessory mount in one compact unit.
- A 40 mm jaw opening supports a range of common rods and tubes within that diameter.
- The 1/4-inch screw fits many small camera and video accessories.
- The rubber clamp pad helps reduce direct contact between the clamp and the mounted surface.
Consider before buying
- The clamp's stated 40 mm opening makes it unsuitable for supports wider than that.
- Conflicting maximum-load figures make it difficult to choose a setup based on a precise capacity; plan conservatively.
- A ball head and single locking knob may be less suitable when a rig needs separate control over multiple joints.
Who Should Buy SmallRig Ballhead Clamp?
Good fit
Consider this mount if your DIY camera setup needs a compact way to attach a lightweight accessory to a rod, tube, or compatible shoe mount.
The 360-degree ball head can help you angle a monitor or light without adding a longer articulated arm, and the 1/4-inch screw supports common accessory connections.
Before choosing it, measure the support where the clamp will sit and confirm it is no wider than the 40 mm opening.
Check that your accessory accepts a 1/4-inch screw, then allow a generous margin below the listed load figures because the supplied details do not agree on the maximum.
Who should skip it
Skip this configuration if the support is wider than 40 mm, the accessory uses a different connection and you do not have a compatible adapter, or the rig depends on a precise load rating.
For a heavier accessory, choose a mount whose verified capacity comfortably covers the complete setup.
How the SmallRig Ballhead Clamp Fits a DIY Camera Rig
Clamp range and placement
The clamp's opening of up to 40 mm defines where it can attach.
Measure the rod or tube at the intended mounting point, including any coating or shape that could affect seating, and make sure the rubber pad contacts the support evenly.
This is a useful fit check before planning accessory placement.
A short route to accessory positioning
The top 1/4-inch screw and 360-degree ball head put the accessory directly on the clamp, so the arrangement can stay compact.
That can help when placing a monitor or light close to a support, while buyers needing more distance or additional positioning joints should check whether a longer arm better suits the rig.
Planning around load information
The product data includes more than one maximum-load figure, so it does not support a precise capacity recommendation.
Keep the accessory and any attached cable strain modest, secure the locking knob, and use a conservative margin; dynamic movement or an off-center load calls for particular care.
Material and contact surface
An aluminum-alloy body and a dense rubber clamp pad are intended for a metal mount with a more forgiving contact surface.
The pad may help limit scratching where the clamp grips, but the support still needs to be compatible in shape and diameter, and the clamp should be tightened without forcing it.
Alternatives to SmallRig Ballhead Clamp
Camera Mounts & Clamps alternative

8,000+ ratings
Read Amazon ReviewsSmallRig Double Ball Head Super Clamp Mount Magic Arm (1138)
Choose the 2164-CF if its compact clamp arrangement and 40 mm jaw fit your support.
Consider the 1138 if you want the included action-camera adapter or a clamp described for table and frame mounting; check its own fit and load limits for your setup.
- The 1138 combines a super clamp and double ball-head mount, includes an action-camera adapter, and is described for rods, tubes, tables, and frames.
- Its listed maximum capacity is up to 1.5 kg.
- The reviewed 2164-CF uses a clamp opening up to 40 mm and places a 1/4-inch screw on its articulated ball head.
Camera Mounts & Clamps alternative

3,000+ ratings
Read Amazon ReviewsSmallRig 9.8-Inch Magic Arm Clamp Kit (2732)
The 2164-CF is the more compact choice when a short mount is enough and the support fits its 40 mm opening.
The 2732 is worth considering when you need an arm to extend the accessory farther from the support or need its broader clamp range and additional threaded interfaces.
- The 2732 pairs a super clamp with a 9.8-inch articulating arm, has 1/4-inch and 3/8-inch clamp threads, and lists a clamp range from 15 mm to 54 mm.
- The 2164-CF keeps the accessory close to a clamp base and lists a maximum jaw opening of 40 mm.
Is SmallRig Ballhead Clamp Worth It?
The SmallRig 2164-CF Ballhead Clamp Double Ball Adapter is worth considering for a compact DIY camera rig that needs a 1/4-inch accessory connection and a clamp that fits a support up to 40 mm wide.
Its adjustable ball head, metal construction, and rubber-padded clamp area make it a flexible mounting option for small accessories.
Confirm the support dimensions and accessory thread before buying, and treat the load capacity conservatively because the supplied figures conflict.
It is a sensible fit for a lightweight, carefully checked setup; buyers who need more reach or a dependable capacity for heavier gear should look for a mount specified for those needs.
Your review at a glance

1,000+ ratings
Read Amazon ReviewsSmallRig 2164-CF Ballhead Clamp Double Ball Adapter
A compact mounting option for DIY camera rigs that need to clamp onto a rod or tube and position a monitor, light, or small accessory.
- The bottom clamp jaws open up to 40 mm for attachment to compatible rods, tubes, or other supports.
- A 1/4-inch screw at the top provides a connection for a monitor, video light, microphone, or similar accessory.
- The double ball-head design provides 360-degree articulation for adjusting the accessory's angle.
- The single locking knob is intended to secure the joint and support quick adjustment.